Item # HTSN13750XXX, Hex Thick Slotted Nut, 1-3/8" Nominal Dia. On Sales Systems Ltd.

Unification. Bold type indicates products unified dimensionally with British and Canadian standards. Unification of fine thread products is limited to sizes 1 in. and under.
Tops and Bearing Surface of Nuts. Nuts in sizes 5/8 in. nominal size and smaller shall be double chamfered. Larger size nuts shall be double chamfered or have washer faced bearing surface and chamfered top.
The diameter of chamfer circle on double chamfered nuts and diameter of washer face shall be within the limits of the maximum width across flats and 95 percent of the minimum width across flats.
The tops of washer faced nuts shall be flat and the diameter of chamfer circle shall be equal to the maximum width across flats within a tolerance of minus 15 percent. The length of chamfer at hex corners shall be from 5 to 15 percent of the basic thread diameter. The surface of chamfer may be slightly convex or rounded.
Bearing surface shall be flat and perpendicular to the axis of the threaded hole within the FIM limits specified for the respective strength level.
Width Across Flats. Maximum width across flats shall not be exceeded. No transverse section through the nut between 25 and 75 percent of the actual nut thickness as measured from the bearing surface shall be less than the minimum width across flats. For milled-from-bar nuts, see statement in General Data pertaining to the nominal bar size to be used.
Corner Fill. A rounding or lack of fill at junction of hex corners with chamfer shall be permissible provided the minimum width across corners is within specified limits at and beyond a distance equal to 17.5 percent of the basic thread diameter from the chamfered faces.

Unit of Measure

Manufacturer | Specifications | Codes and Standards | Runout of Bearing Face, FIM

Manufacturer

N/A Industrial Fasteners Institute

Specifications

Product	N/A Nuts
Unit of Measure	N/A English
Nominal Size or Basic Major Dia. of Thread	N/A 1-3/8 in
Nominal Size or Basic Major Dia. of Thread (Decimal)	N/A 1.3750 in
Basic Width Across Flats (F)	N/A 2-1/16 in
Max. Width Across Flats (F)	N/A 2.062 in
Min. Width Across Flats (F)	N/A 1.994 in
Max. Width Across Corners (G)	N/A 2.382 in
Min. Width Across Corners (G)	N/A 2.273 in
Basic Thickness (H)	N/A 1-3/8 in
Max. Thickness (H)	N/A 1.399 in
Min. Thickness (H)	N/A 1.351 in
Max. Unslotted Thickness (T)	N/A 1.02 in
Min. Unslotted Thickness (T)	N/A 0.98 in
Max. Width of Slot (S)	N/A 0.40 in
Min. Width of Slot (S)	N/A 0.31 in

Codes and Standards

N/A ASME/ANSI B18.2.2 1987 (R 1999)

Runout of Bearing Face, FIM

Runout of Bearing Surface FIM

N/A 0.036 in

Manufacturer

Manufacturer

Specifications

Product

Unit of Measure

Nominal Size or Basic Major Dia. of Thread

Nominal Size or Basic Major Dia. of Thread (Decimal)

Basic Width Across Flats (F)

Max. Width Across Flats (F)

Min. Width Across Flats (F)

Max. Width Across Corners (G)

Min. Width Across Corners (G)

Basic Thickness (H)

Max. Thickness (H)

Min. Thickness (H)

Max. Unslotted Thickness (T)

Min. Unslotted Thickness (T)

Max. Width of Slot (S)

Min. Width of Slot (S)

Codes and Standards

Codes and Standards

Runout of Bearing Face, FIM

Runout of Bearing Surface FIM