Email Us Today: 
Call Us Toll Free: 
Hex Nuts
hex-nuts-2
Bearing Surface. Bearing surface shall be at right angle to axis of the threaded hole within a tolerance of 2 degrees; therefore, the maximum total angularity of bearing surface would equal the tangent of specified angle times the diameter of the flange. Concentricity of Tapped Hole. Axis of tapped hole shall be concentric with axis of nut body within a tolerance equal to 3 percent (6 percent FIM) of the maximum width across flats. Countersink. Tapped hole shall be countersunk on the bearing face and may be countersunk on the top. The maximum countersunk diameter shall be the thread basic (nominal) major diameter plus 0.030 in. for 3/8 in. nominal size nuts and smaller, and 1.08 times the basic major diameter for nuts larger than 3/8 in. No part of the threaded portion shall project beyond the bearing surface. Threads. Threads shall be Unified coarse or fine thread series (UNC or UNF series), Class 2B, in accordance with ASME B1.1. Material. Unless otherwise specified, chemical and mechanical properties of steel nuts shall conform with ASTM A563, Grade A, or SAE J995, Grade 2. Nuts of other materials such as corrosion resistant (stainless) steel, brass, bronze and aluminum alloys shall have properties as agreed between the manufacturer and purchaser. The properties for nuts of several grades of corrosion resistant steel alloys are covered in ASTM F594, and of several nonferrous materials in ASTM F467. Nominal Size. Where specifying nominal size in decimals, zeros preceding the decimal and in the fourth decimal place shall be omitted.
/Asset/a1176.jpg
Bearing Surface. Bearing surface shall be at right angle to axis of the threaded hole within a tolerance of 2 degrees; therefore, the maximum total angularity of bearing surface would equal the tangent of specified angle times the diameter of the flange. Concentricity of Tapped Hole. Axis of tapped hole shall be concentric with axis of nut body within a tolerance equal to 3 percent (6 percent FIM) of the maximum width across flats. Countersink. Tapped hole shall be countersunk on the bearing face and may be countersunk on the top. The maximum countersunk diameter shall be the thread basic (nominal) major diameter plus 0.030 in. for 3/8 in. nominal size nuts and smaller, and 1.08 times the basic major diameter for nuts larger than 3/8 in. No part of the threaded portion shall project beyond the bearing surface. Threads. Threads shall be Unified coarse or fine thread series (UNC or UNF series), Class 2B, in accordance with ASME B1.1. Material. Unless otherwise specified, chemical and mechanical properties of steel nuts shall conform with ASTM A563, Grade A, or SAE J995, Grade 2. Nuts of other materials such as corrosion resistant (stainless) steel, brass, bronze and aluminum alloys shall have properties as agreed between the manufacturer and purchaser. The properties for nuts of several grades of corrosion resistant steel alloys are covered in ASTM F594, and of several nonferrous materials in ASTM F467. Nominal Size. Where specifying nominal size in decimals, zeros preceding the decimal and in the fourth decimal place shall be omitted.
/Asset/a1176.jpg
Stamped with Mfr. ID plus "20"
Chemical and physical reports available upon request at no charge /Asset/1165_Finished-Hex-Nuts.jpg
Chemical and physical reports available upon request at no charge.
Manufactured by Robbins Manufacturing Co; inc. /Asset/nut.JPG
Hex Flange Nuts
(12)- Tops of Nuts.
Large Hex Flange Nuts
(7)- Tops of Nuts.
Hex Coupling Nuts
(34) IFI-128 is a standard developed through the procedures of Industrial Fasteners Institute. IFI-128 was first published in 1978 and reaffirmed, without technical change, in 1986 and in 2000. /Asset/a1174.jpg Alloy 20 Finished Hex Nuts
(4) Manufactured by Robins Manufacturing co; Inc.Stamped with Mfr. ID plus "20"
Chemical and physical reports available upon request at no charge /Asset/1165_Finished-Hex-Nuts.jpg
316L - Low Carbon Finished Hex Nuts
(4) Stamped with Mfr. ID plus "316L"Chemical and physical reports available upon request at no charge.
Manufactured by Robbins Manufacturing Co; inc. /Asset/nut.JPG
Hex Machine Screw Nuts
(13)- Hexagon machine screw nuts shall have tops flat with chamfered corners. Diameter of top circle shall be equal to the maximum width across flats within a tolerance of minus 15 percent. The bearing surface shall be perpendicular to the axis of the threaded hole pitch cylinder within a tolerance of 4 deg.
- Bottoms of hexagon machine screw nuts are normally flat, but for special purposes may be chamfered, if so specified by purchaser.
- Where specifying nominal size in decimals, zeros preceding decimal and in the fourth decimal place shall be omitted.
