Notes:
  • Dimensional Conformance. Beveled washers shall have the following characteristics inspected to ASME B18.18.2, to the inspection levels shown :
    Inside diameter - Inspection Level B
    Visual - Inspection Level C
    If verifiable in-process inspection is used.
  • Non-clipped washers may be rectangular providing neither side dimension is less than L, and one side may be longer than that of the L min included in the table.
  • Nominal washer sizes are intended for use with comparable nominal bolt diameters.
  • Clipped edge E shall not be closer than 0.875 times the nominal bolt diameter from the center of the washer.
Designated characteristics shall be inspected in accordance with ASME B18.18.2. For nondesignated characteristics, the provision of B18.18.1 shall apply. Should a non-designated dimension be determined to be outside its specified limits, it shall be deemed conforming to this standard if the user, who is the installer, accepts the dimension based on fit, form, and function considerations. Where verifiable in-process inspection is used..
1 - 9 of 9 | Results Per Page | View | Unit of Measure
1 

Item #

Description

Nominal Washer Size

Nominal Washer (A)

L

T

E

Sort by
N/A Hardened Beveled Washer with Slope or Taper in Thickness 1:6, 1/2" Nominal Dia. N/A 1/2 in N/A 0.531 in N/A 1.750 in N/A 0.313 in N/A 0.438 in
N/A Hardened Beveled Washer with Slope or Taper in Thickness 1:6, 5/8" Nominal Dia. N/A 5/8 in N/A 0.688 in N/A 1.750 in N/A 0.313 in N/A 0.547 in
N/A Hardened Beveled Washer with Slope or Taper in Thickness 1:6, 3/4" Nominal Dia. N/A 3/4 in N/A 0.813 in N/A 1.750 in N/A 0.313 in N/A 0.656 in
N/A Hardened Beveled Washer with Slope or Taper in Thickness 1:6, 7/8" Nominal Dia. N/A 7/8 in N/A 0.938 in N/A 1.750 in N/A 0.313 in N/A 0.766 in
N/A Hardened Beveled Washer with Slope or Taper in Thickness 1:6, 1" Nominal Dia. N/A 1 in N/A 1.125 in N/A 1.750 in N/A 0.313 in N/A 0.875 in
N/A Hardened Beveled Washer with Slope or Taper in Thickness 1:6, 1-1/8" Nominal Dia. N/A 1-1/8 in N/A 1.250 in N/A 2.250 in N/A 0.313 in N/A 0.984 in
N/A Hardened Beveled Washer with Slope or Taper in Thickness 1:6, 1-1/4" Nominal Dia. N/A 1-1/4 in N/A 1.375 in N/A 2.250 in N/A 0.313 in N/A 1.094 in
N/A Hardened Beveled Washer with Slope or Taper in Thickness 1:6, 1-3/8" Nominal Dia. N/A 1-3/8 in N/A 1.500 in N/A 2.250 in N/A 0.313 in N/A 1.203 in
N/A Hardened Beveled Washer with Slope or Taper in Thickness 1:6, 1-1/2" Nominal Dia. N/A 1-1/2 in N/A 1.625 in N/A 2.250 in N/A 0.313 in N/A 1.313 in
1 - 9 of 9 | Results Per Page | View | Unit of Measure
1 
Use trailing wildcard (*) for broader results.